Graco Inc. 150 RPX Uživatelský manuál

ti8468aOperating Instructions150 RPX Pressure Rollerand Spray SystemTable of ContentsWarnings 2. . . . . . . . . . . . . . . . . . . . . . . . . Press

10 3093885. Screw Power Flush attachment (included withsprayer) onto garden hose and OPEN PowerFlush attachment.6. Screw garden hose and Power Flushat

113093881. Turn power switch OFF.Priming – For flushing water and loading pump and hose with paint2. Turn Power Flush to closed position andgarden hos

12 3093885. Point In–line Valve into waste pail.Priming – For flushing water and loading pump and hose with paint6. Turn power switch ON.7. When paint

133093881. Engage the In–line Valve safety latch.OperationNOTE: Trigger the In–line Valve brieflyonly when you need more paint. Determinehow often yo

14 309388Operation6. Increase pump pressure only if triggeringIn–line Valve cannot supply enough paintfor your rolling speed.7. Whenever you stop pain

15309388Rolling Techniques1. Rolling vertically, roll out the letter “M”.2. Cross roll, horizontally, to spread thepaint.3. Finish with light vertical

16 309388Ceilings, Woodwork and Walls1. Ceilings: Using a paint brush, apply astarting row of paint approximately thewidth of your brush where the wa

17309388Cleanup1. Relieve the pressure. Turn power switchOFF.2. Remove roller cover and diffuser from roller frameas follows:a. Using your thumb, sli

18 3093883. Clean roller cover, caps and diffuser with water or acompatible solvent for non–water–based materials.4. Place roller frame in paint pail.

193093887. Turn power switch ON.Cleanup (continued)8. Trigger In–line Valve.9. Turn Spray/Prime valve to SPRAY.10. Continue to trigger In–line Valve u

2 309388SpecificationsThis equipment is not intended for use with flammable or combustible materials used in places such ascabinet shops or other “fac

20 3093881. Relieve pressure, page 6. Turn power switch OFF.2. Screw Power Flush attachment onto garden hose.3. Turn lever to close Power Flush attac

213093885. Connect garden hose to suction tube with Power Flushattachment. Leave prime tube in waste pail.6. Turn lever to open Power Flush attachmen

22 3093889. Place roller frame in waste pail and trigger In–lineValve. Be sure the holes of the roller frame are facinginside the pail.10. Turn Spray

2330938812. Turn Spray/Prime Valve to PRIME.13. Let water flow through sprayer into waste pail for 20 seconds.Cleanup – Power Flushing After Spraying

24 30938815. Close Power Flush. Turn off garden hose.16. Unscrew Power Flush attachment from suction hose.17. Remove roller frame and extension from

253093881. Relieve pressure, page 6.2. Push up on the trigger guard and swing it away fromthe trigger.3. Unscrew the In–line Valve handle from the hou

26 309388Always pump storage fluid through the pumpsystem after cleaning. Water left in the sprayerwill corrode and ruin pump.1. Place suction tube i

273093884. Turn power switch ON.5. Align arrow on the sprayer with the (roller symbol) onthe Pressure Control knob.6. When storage fluid comes out of

28 309388TroubleshootingCheck everything in this Troubleshooting table before you bring the sprayer to a Graco authorized service center.PROBLEM CAUSE

29309388TroubleshootingPROBLEM CAUSE SOLUTIONPump cycles but paint onlydribbles or spurts whentrigger is pulledPressure is set too low. Turn Pressure

3309388SKIN INJECTION HAZARDHigh pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look likejust a cut, but it i

30 309388Fan pattern variesdramatically while spraying orsprayer does not turn onpromptly when resumingspraying.Pressure control switch isworn and cau

31309388NOTE: The needle, diffuser/seat, gasket and lock-nut must be replaced together. They are includedin Repair Kit 218070.Disassembly1. Relieve

32 309388NOTE: The needle, diffuser/seat, gasket and locknutmust be replaced together. They are included in RepairKit 218070.Reassembly1. Guide thre

333093881. Engage In–line Valve safety latch.2. Hold In–line Valve with nozzle straight up.3. Remove trigger guard.Service – Adjusting the Needle on t

34 3093885. Turn adjusting nut 3/4 turn counterclockwise.6. Connect fluid hose. Use a wrench to tighten.7. Prime system. Page 9.Service – Adjusting

35309388Notes

36 309388Parts150 RPX Model 233687Ref.No. Part No. Description Qty.1 15A680 FRAME 12 195697 STRAINER 13 244035 DEFLECTOR, barbed 15 15A473 TUBE, sucti

373093881150 RPX Model 233687 Apply light coat of lithium–based grease.ti8469a4244533164131213326506323525516375741954556162130, 32, 38156858

38 309388Pressure Roller Assembly Model 244279dmkfegbcHINT:When replacing gasket k*) ando-ring (m*), position o-ring first,then press gasket into pla

39309388Notes

4 309388D The sprayer requires a 120V AC, 60 Hz, 15A circuitwith grounding receptacle. Never use an outlet that isnot grounded or an adapter.D Do not

40 309388Parts ListContractort In–line ValveModel 244161Ref.No. Part No. Description Qty.101 218070 NEEDLE–DIFFUSER/SEAT KIT 1102 244193 TRIGGER, valv

41309388PartsTI0667108119111120107106110103102113112114104105a105b105c105d105101Contractort In–line Valve Model 244161

42 309388Technical DataMaximum fluid working pressure – sprayer 2800 psi (19 MPa, 193 bar). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

43309388Notes

44 309388Graco Standard WarrantyGraco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workma

5309388Grounding and Electric RequirementsD Ground solvent pails used when flushing. Follow local code. Useonly conductive, metal pails, placed on a g

6 3093881. Turn power switch OFF and unplug powercord.2. Turn Spray–Prime/Drain valve toPRIME/DRAIN to relieve pressure.Pressure Relief Procedure3. Tu

7309388Contractort In–line ValvePower SwitchPressure Control KnobComponent IdentificationSuction TubeInlet ScreenSpray/Prime ValvePrime/drain position

8 3093881. Turn power switch OFF.2. Connect one end of grounded fluid hoseto the In–line Valve. Use a wrench totighten.Setup3. Connect other end of h

93093881. Turn Spray/Prime valve to PRIME.2. Separate the (smaller) prime tube fromthe (larger) suction tube.Priming – For flushing factory or storage